next up previous contents
Next: Drives, cards, connectors Up: Introduction Previous: The BIOS   Contents

Technical data

My laptop has a Intel Pention IV 2.4 GHz Processor, 256 MB of RAM, an ATI Radeon Mobility 7500 (M7) graphics card with 64MB and a 15 inch TFT screen (1400x1050 pixel). The on-board sound is an ac '97 compatible chip, the ethernet adapter has a RTL 8139 chip, and a modem is also built-in. There is no built-in floppy (you can use an USB floppy, though), only a Combo drive (DVD/CR-RW) and one PCMCIA slot. It has four USB connectors, a firewire and a serial connector at the back, next to an infrared (IrDA) TODO(Schnittstelle). lspci reports the following: 
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 05)
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05)
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05)
00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05)
00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 05)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW
02:02.0 Communication controller: Conexant HSF 56k HSFi Modem (rev 01)
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)
02:04.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev b8)
02:04.1 FireWire (IEEE 1394): Ricoh Co Ltd: Unknown device 0551

The long version (lspci -vv) gives the following output for those who really want to delve into devices: 

einstein:~# lspci -vv
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
        Subsystem: Alpha-Top Corp: Unknown device b730
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
        Capabilities: [e4] #09 [9104]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
                Command: RQ=0 SBA- AGP- 64bit- FW+ Rate=x1

00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 96
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: e0000000-e00fffff
        Prefetchable memory behind bridge: f0000000-f7ffffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 05) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: e0100000-e01fffff
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05) (prog-if 80 [Master])
        Subsystem: Intel Corp. 82801BA IDE U100
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Region 4: I/O ports at 1440 [size=16]

00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05) (prog-if 00 [UHCI])
        Subsystem: Intel Corp.: Unknown device 244b
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 5
        Region 4: I/O ports at 1400 [size=32]

00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
        Subsystem: Intel Corp.: Unknown device 244b
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 10
        Region 4: I/O ports at 1450 [size=16]

00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05) (prog-if 00 [UHCI])
        Subsystem: Intel Corp.: Unknown device 244b
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 11
        Region 4: I/O ports at 1420 [size=32]

00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 05)
        Subsystem: Alpha-Top Corp: Unknown device b730
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 10
        Region 0: I/O ports at 1200 [size=256]
        Region 1: I/O ports at 1300 [size=64]

01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW (prog-if 00 [VGA])
        Subsystem: Alpha-Top Corp: Unknown device b730
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 4
        Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
        Region 1: I/O ports at 2000 [size=256]
        Region 2: Memory at e0000000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at <unassigned> [disabled] [size=128K]
        Capabilities: [58] AGP version 2.0
                Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4
                Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:02.0 Communication controller: Conexant HSF 56k HSFi Modem (rev 01)
        Subsystem: Conexant: Unknown device 2003
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at e0100000 (32-bit, non-prefetchable) [size=64K]
        Region 1: I/O ports at 3400 [size=8]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)
        Subsystem: Alpha-Top Corp: Unknown device b730
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at 3000 [size=256]
        Region 1: Memory at e0110800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:04.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev b8)
        Subsystem: Alpha-Top Corp: Unknown device b730
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 168
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at e0111000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        I/O window 0: 00000000-00000003
        I/O window 1: 00000000-00000003
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001

02:04.1 FireWire (IEEE 1394): Ricoh Co Ltd: Unknown device 0551 (prog-if 10 [OHCI])
        Subsystem: Alpha-Top Corp: Unknown device b730
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 1000ns max)
        Interrupt: pin B routed to IRQ 11
        Region 0: Memory at e0110000 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

I also have a USB mouse, and use the touchpad at the same time (see the XF86 section).


Reinhold Kainhofer 2003-01-10